- #RATIONAL ACOUSTICS SMAART 7 QUICK START GUIDE GENERATOR#
- #RATIONAL ACOUSTICS SMAART 7 QUICK START GUIDE FULL#
- #RATIONAL ACOUSTICS SMAART 7 QUICK START GUIDE LICENSE#
The Delay Finder lets you enter a specific delay time value, increment or decrement the delay time, or run the Delay Finder on the host. You can choose to see magnitude only, phase only, or both.Īll the same controls are available, including magnitude and phase smoothing, decay mode, and delay times. On iPhone, all plots are overlaid on a single screen. Tap the shutter icon to save a screen shot to the iOS device photo roll. Tap the + and - buttons to change the delay in real time, or access the Delay Finder screen (see below)
#RATIONAL ACOUSTICS SMAART 7 QUICK START GUIDE GENERATOR#
Select the magnitude and phase smoothing separately, choose decay modes from None to Infinite, stop and start the measure, and turn the host generator on and off. On iPad, the graphs are shown in split screen mode, phase on the top, and magnitude and coherence on the bottom.Īs with the Spectrum plots, the screen is touch-GUI enabled, so you can zoom in on either axis, or drag a cursor across the screen to read out exact dB, phase, and frequency values. To select a Transfer Function measure, tap the measure button in the upper left corner, tap the Groups arrow to show all of the running groups, and then select the TF group and measure that you would like to see. On the Spectrum graph setup page, select the Spectrograph speed and orientation, normal or high contrast mode, peak tracking off, on, or large, and change hosts if desired.Īnd, from the main screen, you can take a screen shot of the image and store it in your iOS device photo roll. Select the banding, from Octave bands down to 1/48th Octave, select decay modes from None, 1-10 seconds, Infinite, Fast, or Slow.
Use the play / pause button to start or stop the measure.ĭrag a cursor across the screen, to read out the exact dB and frequency of any point on the curve.
#RATIONAL ACOUSTICS SMAART 7 QUICK START GUIDE FULL#
Double-tap the screen to normalize the display to full range, fitting the curves on the screen. The screen is touch-GUI, so you can expand either the dB or frequency scale. On iPhone, you can see the RTA Line curve plotted over the spectrograph. Choose from RTA Bars, RTA Lines, or the Spectrograph.
The spectrum screen can run in split-screen mode (iPad only), or as a single plot. From here, you can easily change to other running measures, or change groups and switch to Transfer Function. Just tap to select a host, and the Spectrum display appears. IRemote searches for active host computers running Smaart 7, and lists them on the startup-screen. To set up your host computer, just make sure it is on the same WiFi LAN as your iOS device, and then go to the Setting->General tab in Smaart 7, and enable the API access, and, if you are running more than one host on the network, make sure your port address is unique. Turn on peak-tracking, use the cursor to read out magnitude, phase, and coherence values, and control everything with an day-to-use touch GUI interface. Run the Delay Finder, or just use the + and - buttons to tweak the delay. This includes Spectrum Plot RTA and Spectrograph, as well as Transfer Function Magnitude, Phase, and Coherence Plots.
#RATIONAL ACOUSTICS SMAART 7 QUICK START GUIDE LICENSE#
Also, a Smaart 7 license is required to run iRemote, which can be obtained from Rational Acoustics.Īny single measurement may be viewed on iRemote. No audio processing is done on the iOS device.
All audio i/o and processing occurs on the host computer, using audio hardware connected to the host. Select any of the measures in any groups that you have set up on your host computer, and even switch between host computers remotely. Or, use iRemote as a second desktop screen, to see two measures at once. Connect to your host computer, and walk around the venue, listening and viewing results at the same time. You can view any single measure that is running on the host computer, and control things like the host generator, and start and stop measures.īuilt on the Smaart 7 public API, iRemote accesses raw data directly from the host computer running Smaart 7, in real time. Using Single-App Mode for Long-Term Noise Monitoring.Troubleshooting In-App Purchase and Standalone App Issues.Belgium, The Netherlands, and Luxembourg.LARSA - Loudspeaker And Room System Analyzer.
0 kommentar(er)
